一、使用方法 

多檔位定時設定 

1.儀器在使用前應充足電，根據采樣需要設置采樣時間，然后波動數碼開關鍵至相應的定時檔位(如“3”位置，此時采樣工作時間為4小時)。并將采用器的電源開關向上打開，此時指示燈亮，表明采樣開始。定時精度可用秒表校核。 

2.儀器在采集氣體時，首先在進氣口接上過濾器，以免將液體或顆粒吸進機內影響流量，如與固體吸附管配套采樣，液體也不能進入吸附管內，以免造成吸附劑膨脹，使儀器不能正常工作。如果不慎吸入機中，應立即注入蒸餾水，清洗幾次，再吸入無水乙醇，并將儀器空載運轉半小時左右，使無水乙醇充分排出，一般都能恢復正常技術指標。 

3.儀器應充足電放置，若長期不使用，每隔2-3個月需要維護性充電一次，以確保電池具有良好的性能。切勿用非本儀器配套的專用電源充電。 

4.儀器處于關機狀態時應將調節閥手柄松開，以免調節閥手柄長期壓迫氣管而影響流量。 

1.采樣前的準備： 

選配內置電池：該儀器應選用6節5#1.5V干電池或1.2V鎳氫高容量充電電池作為內置工作電源。裝備電池應打開電池后蓋，裝入電池盒中，并按開始鍵檢查內置電池電量是否符合儀器工作和采樣要求。如果儀器顯示欠壓或達不到采樣時間要求，應立即充電或改用專用穩定電源供電，充電時間一般需16小時左右。(穩壓電源工作電壓為220V50HZ，輸出電壓9V，電流300MA)。穩壓電源作為工作電源供電應撥至穩壓位，插入電源插孔，并接通220V50HZ交流電源即可。 

二、注意事項 

1.采樣時必須連接過濾器，才能確保采樣工作效能。 

2.在采樣或自動關機時間設定中顯示自動閃爍，表示欠壓，應及時給儀器補充電。(標準充電時間需16小時) 

3.若長時間儀器不使用，應定期每月給電池組進行維護性補充電，以確保電池具有良好的工作性能。